User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Omega 199,type T Temperature Indicator
DATE:                  07-Mar-96
AUTHOR:                User Contributed
REVISION:
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       5
NUMBER OF LINES:       86
STANDARD:              THERM 311806
STANDARD:              ECTRON 1120
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
# Equipment #L5794-1  Equip. Type: Indicator, Temperature;Omega 199,type T
# Notes: You can use either the Ultramite or Ectron, however, the Ultramite
#        TUR is 3.125:1.
#
# Review Approval:_____________________________ Release Date:____/___/____
# Revision Description.

  1.001  ASK+                                      M   X
  1.002  ASK-   R     N              P                            F        W
  1.003  RSLT         =Accuracy:ñ2.5ø Calibrated @ -65 and 225øF ONLY.
  1.004  RSLT         =
  1.005  RSLT         =Reference:

  1.006  OPBR         Will you be using the Ultramite?
  1.007  JMPF         1.011
  1.008  DISP         You are using the ULTRAMITE. Test TUR's are 3.125:1!
  1.009  STD          THERM 311806
  1.010  JMP          3.005
  1.011  DISP         You are using the ECTRON.
  1.012  STD          ECTRON 1120
# ECTRON accuracy section
  1.013  DISP         Allow the ECTRON sufficient time to warm up.
  1.014  DISP         Connect the standard to the UUT using type T extension
  1.014  DISP         wire. Configure the ECTRON for type T/øF output.
  1.015  HEAD         -65 degrees
  1.016  DISP         Drive the UUT to indicate -65øF
  1.017  ACC          -65.00øF       0.018%
  1.018  MEMI         Enter the ECTRON indicated value @ UUT = -65øF
  1.019  MEMC         øF             2.5U
#!          Test Tol 2.5, Sys Tol 0.0117, TUR 213.675 (>= 4.00).

  2.001  HEAD         225 degrees
  2.002  DISP         Drive the UUT to indicate 225øF
  2.003  ACC          225.00øF       0.018%
  2.004  MEMI         Enter the ECTRON indicated value @ UUT = 225øF
  2.005  MEMC         øF             2.5U
#!          Test Tol 2.5, Sys Tol 0.0405, TUR 61.7284 (>= 4.00).
  3.001  JMP          5.001

# ULTRAMITE accuracy section
  3.002  RSLT         =
  3.003  DISP         {The TUR for the following tests is 3.125:1}
  3.004  RSLT         =
  3.005  DISP         Connect the ULTRAMITE to the UUT using type T extension
  3.005  DISP         wire. Configure the ULTRAMITE for type T/øF output.
  3.006  HEAD         -65 degrees
  3.007  DISP         Drive the UUT to indicate -65øF
  3.008  ACC          -65.00øF       0.8U
  3.009  MEMI         Enter the ULTRAMITE indicated value @ UUT = -65øF
  3.010  MEMC         øF             2.5U
#! WARNING: Test Tol 2.5, Sys Tol 0.8, TUR 3.1250 (<  4.00).

  4.001  HEAD         225 degrees
  4.002  DISP         Drive the UUT to indicate 225øF
  4.003  ACC          225.00øF       0.8U
  4.004  MEMI         Enter the ULTRAMITE indicated value @ UUT = 225øF
  4.005  MEMC         øF             2.5U
#! WARNING: Test Tol 2.5, Sys Tol 0.8, TUR 3.1250 (<  4.00).

  5.001  HEAD         Adjustments
  5.002  PIC          omega199 (20,1,W/BL) "If you need to make adjustments"
  5.003  HEAD
  5.004  DISP         Remove test equipment and reconnect the UUT inputs.
  5.005  DISP         ÿ                 P R O C E D U R E
  5.005  DISP         ÿ     ÿ               COMPLETED!



#! T.U.R.s less than 4.00:                  2
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.